BLACKHAWK SERPA Level 3 Auto Lock Duty Holster - Matte Finish

I bought this solely for use in armed security. The included belt attachment is annoying in that it doesn't allow you to slide the rig forward or back once it's on there, making it a royal pain to find exactly where you want it to be on your belt before you cinch down the screws to permanently secure it. Also, the low-hanging position of the belt mount is uncomfortable as heck when you're sitting in a vehicle (especially one with a center console), because it makes the holster dig into your thigh. The mid- or high-position mounts available for the SERPA holsters are MUCH better and pretty much a must-get.The Level III retention device takes a little bit of extra practice, just enough that you need to get in the habit of keeping your thumb stiff so it can push the button that disengages the top retention piece, but I've compared my draw-and-shoot times with a shot timer and it comes out to be almost exactly the same with this holster as it does with my Level II SERPA duty holster. The top retention piece flips back far enough out of the way that it doesn't hang up on the rear sight and doesn't interfere with the draw stroke at all, so you don't have to really do anything different in that sense. However, you do have to draw upwards just an inch or so higher with this holster to clear it during the draw stroke versus the non-duty SERPA holsters, since these have that extra bit of protective shell going up the FULL length of the slide instead of just half or three-quarters of it. Also, re-engaging the top lock is an extra step, and a little awkward, but even if you just re-holster the pistol like any other SERPA holster, it still clicks securely into place and it's not like your gun is going to fall out or anything if you don't snap that top part closed.Otherwise, this is just like any other SERPA holster in that it's simple, rugged, functional, secure, and nice-looking.EXTRA BONUS: I bought this to fit a full-size Smith & Wesson M&P45, but it also perfectly fits my SD9VE, as well as my Glock 30 (it will also fit a Glock 21 or 20), so the extra versatility is kind of handy if you own more than one pistol of a similar size group.

This was purchased for a Springfield Armory XDM Elite 10mm and the handgun fits PERFECTLY. It is a little longer than the 3.8" but the 4.5 inch would fill the length. The only way you can tell the handgun is shorter than the holster is if you looked or stuck your finger in the bottom. Since the holster accommodates the 3.8 up to the 4.5 you you have to expect this. I do wish they made this holster with the option of having a red dot and/or a light.I have to reiterate that I am extremely pleased with the way the handgun fit into the holster, locked into place and then how the hood perfectly covered the rear of the slide.I have read some reviews about holsters that have a trigger finger release and people complain that their finger slips into the trigger when the handgun is drawn from the holster creating the possibility of an accidental discharge. The location of the release on this holster puts your trigger finger even with the slide ABOVE the trigger. I do not see how this design would cause your finger to slip onto the trigger. I have never tried any of the other trigger finger release holsters but this one must be designed differently because it makes you place your finger exactly where it should be above and off the trigger.

I had been looking for a holster for my Beretta for a long time. I even tried other brands but nothing satisfied me. Then I saw this BLACKHAWK SERPA Level 3 Holster - Automatic Locking Gun Holster, Matte Finish. I loved it from the start. Functional, elegant, and fits incredibly almost perfectly. Its finish and carbon fiber material make this holster the best. I recommend it 💯

I bought this holster years ago, when Safariland's quality control went down the tubes.This is a very fast, very reliable holster.Note: You MUST learn how to properly draw and present a firearm if you intend to carry it holstered. When the draw is complete and you are holding or aiming your gun, your trigger finger MUST REMAIN INDEXED along the side of the frame. These holsters got a bad rap because rookie shooters were pushing the release button, drawing their pistol, then allowing their trigger finger to snap off the holster and onto the trigger, causing a negligent discharge.I've been drawing with this holster, as well as the concealed model, for roughly 15 years with absolutely no problems. KEEP YOUR FINGER INDEXED when you draw, and don't put this holster to work until that is a well established habit.This is not difficult...in fact, this should be the way everybody is taught to draw.When properly used, this is an exceedingly fast holster. I promise indexing is not going to slow you down.The retention devices will not slow down a proper draw.It is easy to get a proper, high grip on the pistol.I recommend this holster to everybody who carries. Too many folks, including well trained, experienced law enforcement officers, have been killed after their guns got snatched. A retention holster is another layer between you and death, and probably the cheapest thing you can do to increase your and your partner's safety.Highly Recommend!

The holster looks great BUT! Didn’t fit my Springfield XD Mod 2 Tactical 9mm.

This is the second Blackhawk SERPA I have purchased. The first for a Glock 22 and this one for a Springfield XDM Elite 9mm. Just like the first one, this one is sturdy and reliable. It fits the weapon like a glove and keeps the weapon secure because it is a level 3. It also allows for a quick draw if the situation requires it. Blackhawk knows what they're doing when it comes to making holsters. After many years, the first holster is still going strong so I know this holster will last the test of time. This was a great purchase and will return, if I need another for another weapon.

Works well, fits well, made well. Blackhawk doesn't disappoint

Works well. Good product.