TRUE MODS LED Brake Tail Light for Harley Davidson - DOT Claw-Design License On Top Square Smoked Rear Red Stop Lamp Assembly for Sportster Dyna Fatboy Road King Electra Glide Ultra Softail Heritage

Great price compared to others. A lot brighter than stock.

This looks great on my heritage. It is very bright and alerts other drivers.

Looks awesome and quality is great very happy overall. What helped me the most was another’s person’s picture of the wire instructions here in the comments. written Instructions were good but guess I’m more of a visual guy to follow instructions. What I struggled the most was the fitment of the whole assembly unit back to the bike. Due to the hard rubber gasket it has a lot of resistance while trying to tighten the screws where I needed a second person to press the unit down while I screwed the screws BUT other than that it was worth it. Overall took me around 25mins

The media could not be loaded. I purchased this for my 2022 low rider s and it was not plug and play I ended up cutting the wires from my original rear blinkers and soldered them onto the new tail light it ended up working but you are going to need a little extra wire to route it under the rear fender I used 16G wire. It was also a really really tight fit just putting the whole assembly on the rear fender I needed to take the old screws front the oem taillight which were to big for the new tail light which made me drill out a bigger hole. But the lights work great

This brake/turn light is bright and looks great! Fit was perfect on my ‘06 HD Sporster XL1200L.

Wired according to the instructions. On the right and left turn signal wire assemblies, each had two extra wires plugged into a connector that didn't connect to anything but just got in the way of installing the light on the bike.When I finally installed the light:-only the middle LED light shows up RED as a running light. The two outside LEDs are not lit.-when the turn signals are engaged, both outside LEDs blink, with the right one brighter when it's engaged and the left one brighter when it's engaged. The opposite LED should always be completely turned off when not engaged-When the brake is engaged, the middle LED doesn't get any brighter than when it's a running light, and the two outside LEDs light up, but as YELLOW lights, not red.Not impressed, and I was hoping to be. I contacted the manufacturer to ask about the extra wires that don't connect to anything. If they say they are designed for international models, then I'm returning it. If they say they're for grounding or something then I may have to eat it, bc I clipped them to make room for the installation. BTW, I asked if this unit fit my 2013 Fatboy. I got an answer that it didUPDATE: the two sets of wires and connectors that supposedly went nowhere could in fact be used. The seller said the turn signal wires (black color) coming from the circuit board could be plugged into these connectors (white) which are attached to blue turn signal connectors that would plugged into the circuit board. Confused yet?It actually makes sense to me now. It wasn't very clear on the instructions though. Speaking of which, the light came with instructions to install a headlight. I contacted the seller for the taillight version and they sent me on in an email.Overall, not a great experience, but the seller was great. Very helpful. Too bad the instructions were incomplete and I couldn't figure out the extra wiring.Even if I had done it right, I'm not sure it would have fit. As it was, it was tough installing it. It's a little bit bigger than the stock tail light but with the extra wiring it was a pretty tight fit. I may look elsewhere.The product itself was really good. If you buy it, just make sure it fits your model and you understand the wiring configuration.Update: the seller went above and beyond customer service expectations. I explained the situation and that I cut the two "extra" wires. I told them that because I did that, I knew the unit was not returnable. They sent me a new one and a return shipping label for the one I messed up! Unfortunately, that one didn't work even though I wired it right, so got a refund on that one. The product MAY work on some bikes, but didn't on mine. It was so-so at best. The seller was absolutely OUTSTANDING! CLASS ACT!

One of the better things I purchased for my bike… this took a few times of tightening it down to get it to seal correctly. Still on my bike and works great and very bright. Looks sharp and highly recommend if your still running a stock bulb on older bikes

Bought for a 2020 Low Rider S. The description said it was plug and play, which is not fully true. The brake light is but I had to cut the connector off my stock turn signals, solder them to the tail light wiring and extend them about a foot each to make the turn signals work. This took a whole lot longer to install than expected because of that extra work. This should have come with a new harness for the turn signals, if it's advertised as plug and play. I reached out to the seller asking about this and got a response 2 days later asking for an order number. Needless to say, unless you want to go a week with the bike torn apart, reaching out to the seller is pretty much useless. Once installed, the light looks and functions great, which is why I gave 2 stars. I wouldn't buy this again though because of needing to cut my stock turn signal connector off. I like to keep all original parts for when my grandkids want to restore the bike back to original 40 years from now : )